Welcome to Wellcraft Boats Owners Forum

We are a boating forum for owners of Wellcraft Boats to enthusiastically discuss all aspects of Wellcraft Boat ownership. Whether you are looking for your first Wellcraft or currently own one, you are sure to feel at home on WellcraftBoatOwners.com

You are currently viewing our board as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have access to searching the forum topics, post topics, communicate privately with other members (PM), respond to polls, upload your own photos and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

  • Global announcements
    Replies
    Views
    Last post

  • Latest news

View the latest post Hello from Norway


Hello everyone. I have a 1988 Wellcraft St. Tropez, with twin Volvo TAMD41A Diesels engines.
The boat is imported from Florida in 2008, and is now situated in "Oslofjorden" (Norway)

Views: 2511  •  Comments: 0  •  Write comments

View the latest post Looking for a reputable propeller repair!


Hello everyone I am looking for a good propeller repair company for my 1997 wellcraft excel 21 SL. It is a little dinged up and just looking for someone to repair at a reasonable price! Thanks Andy

Views: 3370  •  Comments: 2  •  Write comments

View the latest post rub rail


Would anyone know what brand of rail trim was used on a '99 2600, Taco or Barbour,? the plastic trim that holds vinyl trim pc.is what Im asking about, see both products avail. but would like to know brand for sure, pics. are hard to tell if xact, so can cut out section and replace. Thanks Jim

Views: 3341  •  Comments: 1  •  Write comments [ Read all ]

View the latest post lifting and setting 43' portofino


I just purchased a 1988 43' Portofino and it's time to put her up for winter. There are no sling location markings near the rub rail indicating proper sling lift points. Anyone here know where the boats should be lifted and where the boat should be cribbed underneath? IE: Bulkhead locations.
It appears someone has lifted the boat in the wrong location, in the past. The port side rub-rail, between bow and mid-ship, seems to have been pulled up by boat sling while hauling??
Thanks in advance,
Lawrence

Views: 2858  •  Comments: 0  •  Write comments [ Read all ]

View the latest post New coastal owner


last week I bought a 95 coastal 2600
ready for the road trip
Image
Image

on the road with https://www.facebook.com/HighGearTransportCompany
Image

at home now the motor are being rebuilt and I will restore the interior and cockpit
before she goes on the lift
Image
Image
my ongoing restore thread

Views: 2514  •  Comments: 0  •  Write comments [ Read all ]

View the latest post Wellcraft 18 Fish parts


As a new owner of a 1989 Wellcraft 18 Fish, I'm looking for expertise and direction. Can any other members point me in the direction of a parts supplier? I'm looking to replace the seat cushions on the bucket seats....one blew of while returning home with my new prize....I didn't discover it, until I got home after the 2oo mile journey. I'm also looking to reapply the "Wellcraft" decals.
Thanks
Warren

Views: 2733  •  Comments: 0  •  Write comments [ Read all ]

View the latest post Wellcraft 18 Fish sits low in the water


I'm considering the purchase of a 1989 Wellcraft 18 Fish from a local dealer.

The boat appears to be in pretty good shape, given its age. The 150hp Yamaha 2 stroke motor ran well during the sea trial. Here's my concern. While at rest at the dock in calm water, the boat sits quite low in the water. The water level at the stern is approx 4-5 inches above (yes, ABOVE) the two transom scupper outlets . This means that the waterline at the side of the boat towards the stern is about 3-4 inches above the factory waterline decal that is on the boat. I'm concerned about this !!! This means that there is only about 6-7 inches of "free board" remaining to the top of the transom cutout.
There is no additional equipment on board, and only one battery in the port stern locker. The scuppers were plugged with quick snap plugs when we were at the dock, then the salesman removed them as we prepared to get underway.

Is it the weight of the stock original 150hp motor causing this? Is this considered NORMAL for this model?

When we were underway during the sea trial, in 2-3 ft chop, the boat ran fine, planed ok, and steered ok. But on the initial "hole shot" the stern quickly buried itself and 1-2 gallons of wake water quickly splashed over the transom into the motor well, but once on plane it quickly exited through the scuppers, that were now above the water.

Am I just paranoid?...or should I fear that maybe something more serious is causing the low stern, like maybe water in the hull core?
Any help or observations from current or previous owners of this model would be greatly appreciated

Thanks in advance
Warren (Thousand Islands, Ontario)

Views: 9331  •  Comments: 5  •  Write comments [ Read all ]

View the latest post vacuflush toilet


where is the vacuum generator and holding tank located on a 2008 29 coastal?

Views: 2877  •  Comments: 0  •  Write comments

View the latest post Propellers


Hi guys!

I'm new in here, from Norway.
In 2006 I bought a 1996 model 2150 Wellcraft Eclipse with Volvo Penta 5,0 FL with Cobra SX drive. Engine power is 190hp.
Last summer, my engine broke down, and I bought a new one, same engine, just modified to about 305 hp.
Mounted it this season, and was hoping for 50 knop (app 57 mph).
Earlier, with 190hp it went maybe 40 knop.
With my new engine, we have tried different propellers. Different sizes and picth.
The new engine is supposed to run at about 4800rpm.

With my alu propeller 14 1/4x21, my originale propeller in steel 14 1/2,x20, the boat went maybe 42-43 knop.
There was no problem to reach 4800 rpm alone in the boat, or with 5 people. Means that there is more potentiale in the engine and boat.
I borrowed a steel propeller 14 1/2x25. That wass TO heavy. Reached only 4000 rpm, and acceleration was horrible!
Just orderer a new one, steel, 14 1/2x22, haven't got it yet.
But the BIG problem is that the boat seems to not lift itself from the water.
When I'm at 3000 rpm, I can trim the drive, and lift the boat from the water, leaving as little as possible of the boat in the water. That means I will reach higher topspeed. But when at 4000rpm and more, the boat doesn't lift, and you can feel the whole boat beeing in the water. This means it will go slower. When I trim the drive more, it makes a big roostertail instead of lifting the front.

Anybody here that knows anything about this..?

Hoping someone can help me out with this :)

Views: 5791  •  Comments: 0  •  Write comments [ Read all ]

View the latest post need advice


looking at 1999 Martinique 36ft. Engines have 1010 hrs on each. Fresh water 2nd owner. Not sure of engine life if inboards. Had a 19 ft American for 25 yrs. Great boat. Thanks cje

Views: 7998  •  Comments: 2  •  Write comments


  • The Sand Bar
    It's time to kick back with a cool one at the Sand Bar and talk about something else for a while! This forum is for all non-boating related discussions. NO POLITICS! The general forum rules apply, so don't co crazy :-)
    11 Topics
    37 Posts
    Last post Re: NFL Playoffs
    by willy View the latest post
    Fri Jan 13, 2023 7:39 am



  •  Newest members

  •  Top Posters

  •  Statistics
  • Totals
    Total posts 5733
    Total topics 2083
    Total Announcements: 0
    Total Stickies: 0
    Total Attachments: 1136

    Topics per day: 0
    Posts per day: 1
    Users per day: 1
    Topics per user: 0
    Posts per user: 1
    Posts per topic: 3

    Total members 5080
    Our newest member matthewmiller

  •  Who is online?
  • In total there are 85 users online :: 2 registered, 0 hidden and 83 guests

    Registered users: Google [Bot], Google Adsense [Bot]


  •  Sponsors

  •  Link to us
  • Please feel free to link to Wellcraft Boat Owners Forum. Use the following HTML:



  •  Clock