I’m looking for a used Yamaha 300 saltwater series. Any help is appreciated

Hi

My name is Carlo. I have just purchased a 2002 3300 Martinique in Ontario Canada. I live in Halifax, Nova Scotia. I am have the boat shipped here on a low boy transport.
I just sold my Bayliner 4788 that we enjoyed for 10 years. We are down sizing due to boating requirements.

Looking forward to learning about the boat I purchased.

Carlo

I HAVE 2000 EVINRUDE RAM FICHT 175 OUTBOARD WITH CONTROLS, MANUAL. iT HAS 466 HOURS ON IT. I REPOWERED MY BOAT BECAUSE NO ONE CHECKED
THE OIL-MIX TANK. IT HAD WATER IN IT. SEVERAL THOUSAND DOLLARS LATER I LEARNED THIS BECAUSE OF INCOMPETENT BOAT REPAIR SHOP.
PRICE $3400, THIS IS WHAT ANCHOR MARINE IN MISSOULA,MT WOULD HAVE GIVEN ME FOR TRADE-IN ON A NEW 175 EVINRUDE. CALL 406 363-5411 FOR FURTHER DETAILS.

How do you work on wires, pumps etc. Do you get inside the bilge. It seems that the bilge area is too small to get in; but it is too large to be able to work the pumps from the outside. I am trying to connect underwater light and do not know how to get inside. Any ideas?

Hey all. I've wanted a boat since I was a Kid. I'm 45 now, with a family, one graduated HS this past weekend and a Freshman finishing up. My wife gave me the green light on a Boat, (Once I emptied out the back yard), for a FREE boat and trailer I found on 'Letgo' I just got it pulled in my back yard and the previous owner told me it's a 1971 Wellcraft. With some research I'm finding out the model is an Airslot. Not sure of much else. I believe it's a 17-18 foot. The trailer is in good shape, but needs the wiring redone as the lights don't work.
The floor is dead, so I'm about to start a project with NO experience. I'm just watching a LOT of youtube vids to figure out what I might be in for.
ANY and ALL suggestions and advice would be appreciated! I just pulled up the carpet, and now I'm not sure where to go from there. Hoping to get some cardboard this weekend to map the floor to have a pattern to cut the plywood when I get that far.
Again. If anyone has any suggestions or advice, I would greatly appreciate it. I'm in NH if anyone is local, and can meet up for some tips or checking things out.
Thanks in advance!
Al

Hello all, I have twin mercury (1999) 150 EFI saltwater series outboard, both starts and runs, however, one engine keeps shutting down, it re-starts easily runs for about 3 to 5 minutes, runs high then shuts down again, I've changed fuel filter & water separator to rule out bad gas, and still it keeps shutting down, any HELP?

Hello, I have a 2001 28’ Martinique that I just replaced all the gauges on. After finishing I turned the key one click and no beeping sound and gauges didn’t move. After going over all the wiring (and seeming correct) I cranked the motor which now cranks but doesn’t start. I’m wondering if anyone else had this prob after changing gauges. Original gauges were all analog except the Hr meter on the RPM was digital. The new RPM gauge doesn’t have an hr meter and I’m wondering if that’s inter fearing with the Sea-Fire?? Faria gauges replaced with new Faria. Ty

2000 3300 Martinique. A/C water pump location? Not pushing water to cool condenser. Need to check impeller

I am pretty excited to become a first time boat owner. My wife and I bought a 1990 Wellcraft 192 Sport.

It has been quite a fun experience so far, I have removed years of oxidation. It has gone from dull red to a bright red luster.

We have replaced the exhaust manifolds and risers, Impeller, did a full tune up, and we are looking good!

Hello from East Tennessee. I am a new member to this blog as of today June 10. I own a 1977 Airslot 165. Great boat in great shape. Especially for a 42 year old boat! Mercruiser 140 is original and runs great, Pre-Alpha outdrive works fine. Just replaced all bellows and the gimbal bearing. All electronics work. Interior is in 9/10 condition. Keep in covered dry storage on Chickamauga Lake near Chattanooga. Just a great little boat. Looking forward to discussions with other Airslot owners.