Welcome to Wellcraft Boats Owners Forum

We are a boating forum for owners of Wellcraft Boats to enthusiastically discuss all aspects of Wellcraft Boat ownership. Whether you are looking for your first Wellcraft or currently own one, you are sure to feel at home on WellcraftBoatOwners.com

You are currently viewing our board as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have access to searching the forum topics, post topics, communicate privately with other members (PM), respond to polls, upload your own photos and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

  • Global announcements
    Replies
    Views
    Last post

  • Latest news

View the latest post wellcraft crusier - looking for information


good morning...........new to this forum......i am thinking about the purchase of 1996 wellcraft excel 23SE.........i know wellcraft has a good rep, but since this boat is so old, i have the following questions.....1) can anyone out there tell me about their experiences with this boat? it will be used mainly on inland lakes, but would like to take it to the great lakes.....thoughts on reliability, does the draft represent an issue on inland lakes, etc.............second question, since it is so old, will i have any trouble getting replacement parts?......wellcraft doesn't make this model any longer, i believe, so i know support from the manufacturer.............any information that you can provide will assist in my purchase.....i thank you in advance

Views: 135  •  Comments: 1  •  Write comments [ Read all ]

View the latest post 1993 Coastal 28 exhaust manifold replacement


Hi Gang

I have a small mobile repair business on the South Shore of Mass.

I was recently asked by a potential customer if I would be interested in replacing the manifolds and elbows on his twin inboard RWC 5.7 Mercs.

The outboard manifolds are about a 1/2 inch away from the water tanks on both sides of the motors.

Does anyone have any ideas on how to go about this job?

I’m not a young man. Can’t position my self like Gumby any more and no longer lift motors.

Any advice would be greatly appreciated.

Thank You

Misfit

Views: 177  •  Comments: 1  •  Write comments [ Read all ]

View the latest post 1998 Wellcraft 210 CCF


Hi everyone, I recently picked up a 1998 210 CCF. Where can I find the plastic rings that go inside the holes of the gunnel rod holders and I also need the locking screws for the transom chairs. Any help will be greatly appreciated.

Views: 127  •  Comments: 0  •  Write comments

View the latest post Attachment(s) Stringers and fuel tanks


Picked up an 85 airslot 185, pretty decent shape for its age. My questions are 1) what are the saddle tanks made of and are they a concern? Where are the access points for the tanks? 2) the forward mount stringer is collapsing, has anyone done the 1/2" aluminum stock upgrade? Thanks in advance, love this boat. Lots of character and very unique

Views: 255  •  Comments: 3  •  Write comments [ Read all ]

View the latest post New Guy


Just purchased my first Lake Michigan boat, a 1994 Martinique 3200. Looking forward to learning a lot.
Cheers

Views: 176  •  Comments: 1  •  Write comments

View the latest post Need Information


I have a 1992 21CCF, on the port side I have a black knob on the gunwell, it is connected to a cable that goes to what looks like a cable operated valve can anyone tell me what it is for? The bottom of the hull also has some type of water pick up what is it used for????

Views: 184  •  Comments: 0  •  Write comments [ Read all ]

View the latest post Canvass Cabin for 1989 St. Tropiz


Does anyone know where I can get a Canvass "Cabin" for my 1989 St. Tropiz?

Views: 130  •  Comments: 1  •  Write comments

View the latest post How to Straighten Bent Plastic Window Molding


The starboard side window molding somehow got a bow in it and I want to flatten it to its original shape. I believe this can be done by putting the molding in the oven to soften it and then gently holding gently in the flat. The key is setting the oven just beneath the melting point of the plastic and I'm not sure what that might be for the plastic molding Wellcraft used on my boat. Another possibility is using a hair dryer or heat gun to soften the molding but I don't want to risk blistering it. Anyone done this?

Views: 68  •  Comments: 0  •  Write comments [ Read all ]

View the latest post water / fuel separator


Hi,
Last summer I bought a 1988 Wellcraft 192 Classic. Before I winterized it, I ran the fuel out. After that I have been unable to start it without using starting fluid and having a bear of a time. When I took it to have it shrink wrapped, they could not get it started. They suspect I may have a lot of debris in the carb due to emptying the tank (I put fresh fuel and dry gas in shortly after). They advised me to change the fuel filter / separator. I cannot find a fuel filter / water separator anywhere. The fuel hose comes out of the fuel tank and directly down to the fuel pump then up to the carburetor. Should I install a separator and is this unusual for this boat? They guy I bought it from overhauled the engine and did a really crappy job of it. Thanks for any advice or assistance you can offer.

Views: 169  •  Comments: 3  •  Write comments [ Read all ]

View the latest post Transmissions outdrives rotation


I have an 85 scarab 400 with twin mark iv bowtie blocks and am freshening them up. First thing is do both engines turn the same direction with one transmission converting the prop to turn the opposite way or does the engine turn opposite. Does it matter what serial number is on the transmission to tell if it does or do all of the transmissions turn the same way and it is in the engine. The TRS Drives reflect 330. What other info do i need as trying to get prices on a cam that turns the opposite way is hard. I have one bad lobe on my Solid Roller Comp cam. Both engines are loaded with MSD, Bowtie Blocks, 1050 Dominators, Stellings over the rear headers, Dart intakes etc. Any direction would be great.

Views: 81  •  Comments: 0  •  Write comments [ Read all ]


  • The Sand Bar
    It's time to kick back with a cool one at the Sand Bar and talk about something else for a while! This forum is for all non-boating related discussions. NO POLITICS! The general forum rules apply, so don't co crazy :-)
    2 Topics
    15 Posts
    Last post Boat show Miami
    by goodday View the latest post
    Sat Feb 18, 2017 10:35 am



  •  Newest members

  •  Top Posters

  •  Statistics
  • Totals
    Total posts 2399
    Total topics 1016
    Total Announcements: 0
    Total Stickies: 0
    Total Attachments: 509

    Topics per day: 0
    Posts per day: 1
    Users per day: 1
    Topics per user: 0
    Posts per user: 1
    Posts per topic: 2

    Total members 2574
    Our newest member MindyO

  •  Who is online?
  • In total there are 2 users online :: 1 registered, 0 hidden and 1 guest

    Registered users: Bing [Bot]


  •  Sponsors

  •  Link to us
  • Please feel free to link to Wellcraft Boat Owners Forum. Use the following HTML:



  •  Clock