Welcome to Wellcraft Boats Owners Forum

We are a boating forum for owners of Wellcraft Boats to enthusiastically discuss all aspects of Wellcraft Boat ownership. Whether you are looking for your first Wellcraft or currently own one, you are sure to feel at home on WellcraftBoatOwners.com

You are currently viewing our board as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have access to searching the forum topics, post topics, communicate privately with other members (PM), respond to polls, upload your own photos and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

Bilge pump location

This is a place for general Wellcraft Boats discussions.

Topic author
No Reason
Posts: 2
Joined: Mon Jun 01, 2015 6:40 pm
Vessel Info: 2000 Wellcraft 24 Walkaround

Bilge pump location

Postby No Reason » Mon Jun 01, 2015 6:58 pm

I have a 2000, 24' Walkaround. I am getting getting wet carpet in the cuddy. The rear bilge is dry, I can only assume the forward bilge is holding water, but I do not know how or if there is a forward access to it. Could it be below the plate that supports the table?


Chris
Posts: 23
Joined: Wed Mar 18, 2015 12:01 pm
Vessel Info: '96 23 Excel WA. 200 HP Mercury Offshore XL with a re-manufactured powerhead (2013).
Has thanked: 2 times
Been thanked: 10 times

Re: Bilge pump location

Postby Chris » Tue Jun 02, 2015 12:56 pm

Hi No,

On MY W/A, the forward bilge is located just rear of the forward bulkhead. In order to access the bilge I have to be in the cabin looking aft. There is a hatch located near the floor toward the bottom of the bulkhead. Upon opening the hatch I get access to my forward bilge. Good luck.

Chris
Mount Vernon, VA

Topic author
No Reason
Posts: 2
Joined: Mon Jun 01, 2015 6:40 pm
Vessel Info: 2000 Wellcraft 24 Walkaround

Re: Bilge pump location

Postby No Reason » Tue Jun 09, 2015 8:36 pm

Thanks for your advice. That was exactly where it was. I embarrassingly have to admit I never looked with a flashlight and assumed it was farther forward. The reason I have been so concerned about it is in 1-2’ seas, the carpet in the cuddy is always getting wet even though the aft bilge is staying relatively dry. The drain hole between the cabin and forward bilge compartment doesn’t seem to be blocked, but the drain hole clearly shows standing water. Any idea where it may be coming from?

Chris
Posts: 23
Joined: Wed Mar 18, 2015 12:01 pm
Vessel Info: '96 23 Excel WA. 200 HP Mercury Offshore XL with a re-manufactured powerhead (2013).
Has thanked: 2 times
Been thanked: 10 times

Re: Bilge pump location

Postby Chris » Tue Jun 09, 2015 11:05 pm

A couple of things come to mind

On my boat, when it rains, the rain comes in through the small hatch over the cabin door. There is a piano hinge connecting two horizontal laying plexi pieces that is supposed to be waterproofed by a piece of reinforced rubber. The rubber has worn through and now the rain comes in and wets the carpet right by the hatch that leads to the bilge. I'm currently looking for a replacement piece of reinforced rubber.

The auto switch for my bilge was of the type where the DC wires were directly connected to the actuator which means if the wires are hung up, the switch won't activate properly. I switched mine out.

If you find water coming into the cabin, and your hull is in good shape then check the seam where the deck meets the hull. I've heard of several Wellcraft where the seam separates.

First thing I'd check would be both the auto and manual functionality of the forward bilge. Water from the bilge should be under an inch of so deep when the bilge has just finished cycling.

Good luck and let us know what you find.
Mount Vernon, VA

cliffdweller
Posts: 7
Joined: Sat Jul 19, 2014 9:07 pm
Vessel Info: 2000 22 wellcraft walkaround, 200 2014 etec

Re: Bilge pump location

Postby cliffdweller » Mon Jun 15, 2015 3:50 pm

I have a 2000 WA and had the same problem. If your carpet is getting wet after it rains or you wash your boat, check the seal around your steering wheel. My 22 WA has hydraulic steering and the area where the steering is mounted was not sealed. A lot of the water from the helm ran around the steering and into the cuddy. The water ran down between the fiberglass and the inner vinyl covered wall so the inside wall was never wet to the touch. I sealed around they hydraulic steering and the top of the plastic instrument cover and my carpet stays dry.

Fishin Off
Posts: 3
Joined: Tue May 26, 2015 10:59 am
Vessel Info: 2000 Marinique 2600

Re: Bilge pump location

Postby Fishin Off » Wed Jun 17, 2015 11:24 am

I have a 2000 Martinique 2600 and am tryingn to locate the forward bige pump.Anyone familiar with the location???

Crackers
Posts: 1
Joined: Mon Jun 29, 2015 10:48 am
Vessel Info: 1999 2600 Martineque 7.4 Gi Volvo Penta DP
Been thanked: 2 times

Re: Bilge pump location

Postby Crackers » Mon Jun 29, 2015 11:12 am

On my 1999 2600 Mart. the forward bilge is located in the aft cabin in the floor to your left, lift up mattress
And you will see the cover.

Return to “Wellcraft Boats Forum”



Who is online

Users browsing this forum: No registered users and 1 guest